Lr-baggs iBeam Onboard-Sm User Manual download pdf

INSTALLATION MANUAL & USER'S GUIDE

L.R. BAGGS PICKUPS

TABLE OF CONTENTS

1. Package contents

2. Overview & cautions

3. Removal of previous system (retrofit only)

4. New installation woodworking

4.1. Routing the preamp hole

4.2. Drilling the strapjack hole

5. Strapjack installation

6. iBeam installation: pin bridge guitars

6.1. General positioning guidelines

6.2. Pin bridge installation

7. iBeam installation: non-pin bridge guitars

7.1. General positioning guidelines

7.2. Non-pin bridge installation

8. iBeam installation: classical guitars 

8.1. General positioning guidelines

8.2. Classical installation

9. Alternative placements

10. Preamp installation

11. Controls

12. Specifications

1 . P A C K A G E C O N T E N T S

iBeam:

one (1) iBeam bridge plate transducer

two (2) adhesive strips

one (1) iBeam quick mount fixture kit (included in

steel string system only), including:

one (1) fixture instruction sheet

two (2) threaded posts

two (2) standoffs

two (2) .312" nuts

one (1) fixture board

two (2) small adhesive dots

Onboard Preamp:

one (1) onboard preamp

six (6) ½" black installation screws

six (6) fiber washers

one (1) flexible black preamp bezel

two (2) self-stick wire platforms

one (1) preamp routing template

one (1) .090" x .048" pickup replacement shim

one (1) .120" x .048" pickup replacement shim

one (1) strapjack harness

2 . O V E R V I E W & C A U T I O N S

The iBeam Onboard-Sm is a direct drop-in retrofit system for the smaller “Brand X” onboard pickup system that is often factory-installed on

Martin, Taylor and many other popular guitars. New (non-retrofit) installations can be made simply by routing the appropriately-sized hole in the

guitar’s side to accommodate the preamp and onboard controls. This system includes the iBeam bridge plate transducer and an onboard preamp

with volume, EQ and notch filter controls.

iBEAM ONBOARD-Sm

483 N. FRONTAGE RD.

NIPOMO, CA 93444

WWW.LRBAGGS.COM

1 2 3 4 5 6 7

Summary of Contents

Page 1 - L.R. BAGGS PICKUPS

INSTALLATION MANUAL & USER'S GUIDEL.R. BAGGS PICKUPSTABLE OF CONTENTS1. Package contents2. Overview & cautions 3. Removal of previous sys

Page 2

fig. 1We recommend that this system be installed by a professional dealer/installer. We do not provide installation advice or support for hom

Page 3

4.2 Drilling the strapjack hole: For proper installation, this jack requires a clean 1/2" hole in the tail block of the instr

Page 4 - B R I D G E G U I T A R S

4. Place the stationary rod of the mounting fixture in the high-E bridge pin hole and adjust the movable rod laterally in the slot until

Page 5

to act as a reference when locating the iBeam. The hole locations will correspond to the small slots in the bottom of each end of

Page 6

Note: Do not trim the edges of the pickup if you do not have space between the braces for the pickup. This will both ruin the p

Page 7 - 1 1 . C O N T R O L S

flush on the guitar side's surface.1. Once the bezel has been formed, drop it into the existing cutout and screw the 4 provided screw

Comments to this Manuals

No comments

Lr-baggs iBeam Onboard-Sm User Manual

Browse online or download User Manual for Microphones Lr-baggs iBeam Onboard-Sm. LR Baggs iBeam Onboard-Sm User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Microphones Lr-baggs iBeam Onboard-Sm